mg娱乐场4355手机版

欢迎访问mg娱乐场4355手机版!
贵阳折叠门

联系我们

联系我们:

公司名称:mg娱乐场4355手机版有限公司

联系人:马经理

联系电话:0851-85762816

手机:18985534165

网址:www.gzhwjmy.cn

地址:贵阳市南明区沙冲南路铁路桥旁


简单介绍贵州折叠门?安装步骤及注意事项;

您的当前位置: 首 页 >> 新闻中心 >> 公司新闻

简单介绍贵州折叠门?安装步骤及注意事项;

发布日期:2018-01-21 22:04 文章来源:mg娱乐场4355手机版 点击:

简单介绍贵州折叠门">贵州折叠门安装步骤及注意事项;

贵州折叠门

The installation steps and matters needing attention of the folding door in Guizhou are briefly introduced.


首先我们安装折叠门前要确定安装的位置,如果是作为厨房(厨房装修效果图)门或者厕所门,应该安装在门框中间的位置上;如果作为客厅的隔断(隔断装修效果图),要确定好位置,留出相应的空间,测量一下直线长度,然后确认一下轨道的长度是否正确,如果轨道的比较长,用尺子量好使用长度,做好记号,用钢锯锯掉长出的部分,注意不要让铁屑掉入轨道内,以免影响门的滑动。

First we installed in front of folding to determine the installation position, if it is used as a kitchen (kitchen renovation renderings) the door or the bathroom door, the door should be installed in the middle position; as if the living room partition (partition decoration renderings), to determine a good location, set aside the corresponding space, measure the length of the line. And then confirm the length of the track is correct, if the track is long, with a ruler to use the mark length, with a hacksaw to amputate the longer parts, don't let the iron fall into orbit, so as not to affect the sliding door.


贵州折叠门安装步骤及注意事项

Installation steps and precautions of Guizhou folding door


折叠门安装步骤

Folding door installation steps


1、确定位置,首先我们安装折叠门前要确定安装的位置,如果是作为厨房门或者厕所门,应该安装在门框中间的位置上;如果作为客厅的隔断,要确定好位置,留出相应的空间,测量一下直线长度,然后确认一下轨道的长度是否正确,如果轨道的比较长,用尺子量好使用长度,做好记号,用钢锯锯掉长出的部分,注意不要让铁屑掉入轨道内,以免影响门的滑动。

1, to determine the location, we installed in front of folding to determine the installation position, if it is used as the kitchen door or the bathroom door, the door should be installed in the middle position; as if the living room partition, to determine a good location, set aside the corresponding space, measure the length of straight line, and then confirm the length of the track is correct and if the track is long, with a ruler to use the mark length, with a hacksaw to amputate the longer parts, don't let the iron fall into orbit, so as not to affect the sliding door.


2、插入折叠门,拿起滑道,将折叠门在捆扎的状态下插入滑道,将其推到滑道的中间部位,捆扎的状态更方便安装,推到中间是为了防止在安装的时候不小心滑动,从滑道上掉下。

2, insert the folding door, pick up the slide way, insert the folding door into the slide way in the state of strapping, push it into the middle part of the slide way, the state of the binding is more convenient to install, and push it to the middle to prevent slipping from the slide way when it is installed.


3、固定,在固定之前,要确认好把手的方向,习惯向左还是向右拉,依据习惯选择相应的方向,确认好后开始安装轨道,按照先中间后两边的顺序安装,用冲击钻将螺丝旋入轨道和门框或墙壁,因为门框或者墙壁都比较厚,单纯用螺丝刀很难旋入螺丝,所以要借助冲击钻的力量,安装完螺丝后,解开捆扎折叠门的绳子。

3, fixed, before fixing, confirm that the direction of the handle, used to turn left or right, according to custom select the appropriate direction, confirm the installation after the start of track, according to the center on both sides of the installation sequence, with the impact of drilling the screw is screwed into the rail and the frame or the wall, because the door or walls are relatively thick simple, it is difficult to use a screwdriver screwing screws, so to use percussion drill power, install screw, untie the rope tied folding door.


4、打入胶套,将折叠门拉开,对照门上的吸铁石的位置,确定墙壁或者门框上安装吸铁板的位置,在确定好每个吸铁板位置后,用冲击钻打孔,大概四厘米的深度,然后将胶套打入孔中,然后依次将胶套打入。

4, into the rubber sleeve, the folding doors opened the door, the control of the magnet position, determine the iron wall or door suction installation position, in determining a good position after each suction plate, punch impact drill, about four cm depth, and then the rubber sleeve into the hole, and then turn into the rubber sleeve.


5、固定吸铁板,将折叠门再次推到中间,拿起吸铁板,将其上的孔对准胶套孔的中心,用螺丝刀将螺丝旋入胶套,直到固定住吸铁板,用同样步骤将每个吸铁板都固定好,然后拉开折叠门,将没有把手的一侧与吸铁板吸和,这样就安装好了折叠门。

5, fixed suction plate, the folding door once again pushed to the middle, pick up the suction plate, the rubber sleeve is aligned to a hole on the center of the hole, use a screwdriver to screw is screwed into the rubber sleeve, until the fixed suction plate, using the same steps for each suction plate are fixed, and then open the folding doors, there will be no one side of handle and iron absorption and absorption, which installed the folding door.


相关标签:PVC折叠门

最近浏览:

mg娱乐场4355手机版-mg游戏手机版官方网站|登录